검색결과
-
[특집-기술위원회] TC 213 - 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 213 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)과 관련된 기술위원회는 1996년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는사라 켈리(Miss Sarah Kelly)가 책임지고 있다. 현재 의장은 이안 맥클라우드(Mr Iain Macleod)이며 임기는 2025년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 니콜라 페루(Ms Nicola Perou) 등이다.범위는 기하학적 제품 사양(GPS) 분야의 표준화다. 즉 치수 및 기하학적 공차, 표면 특성 및 관련 검증 원리, 치수 및 기하학적 측정의 불확실성을 포함한 측정 장비 및 교정 요구 사항을 다루는 거시 및 미세 형상 사양이다.표준화에는 기본 레이아웃과 도면 표시(기호)에 대한 설명이 포함된다. 단, 도면 표시(기호)의 특정 비율 및 치수 정의, 실행은 제외된다.현재 ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준은 147개며 ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준은 22개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준 147개 중 15개 목록▷ISO 1:2022 Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties▷ISO 286-1:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits▷ISO 286-1:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits — Technical Corrigendum 1▷ISO 286-2:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts▷ISO 286-2:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts — Technical Corrigendum 1▷ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges▷ISO 463:2006/Cor 1:2007 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1▷ISO 463:2006/Cor 2:2009 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2▷ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out▷ISO 1119:2011 Geometrical product specifications (GPS) — Series of conical tapers and taper angles▷ISO 1660:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing▷ISO 1938-1:2015 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO 1938-2:2017 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges▷ISO 2538-1:2014 Geometrical product specifications (GPS) — Wedges — Part 1: Series of angles and slopes▷ISO 2538-2:2014 Geometrical product specifications (GPS) — Wedges — Part 2: Dimensioning and tolerancing□ ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준 22개 중 15개 목록▷ISO/CD 1938-1 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO/AWI 2768 General tolerances▷ISO/DIS 5059-1 Geometrical product specifications (GPS) — Dimensional measuring equipment: inside micrometers — Part 1: Two-point inside micrometers — Design and metrological characteristics▷ISO/FDIS 5459 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems▷ISO/DIS 5463 Geometrical product specifications (GPS) — Form measuring equipment; Rotary axis form measuring instruments — Design and metrological characteristics▷ISO/CD 10360-102 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 102: The language of symbols G3▷ISO/AWI 12179 Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments▷ISO/DIS 14405-1 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes▷ISO/CD TS 15530-2 Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 2: Part 2: Evaluating task-specific measurement uncertainty by multiple measurement strategies using a single uncalibrated workpiece▷ISO/DIS 16610-21 Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters▷ISO/CD 16610-22 Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters▷ISO/DIS 16610-31 Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters▷ISO/DIS 16610-45 Geometrical product specifications (GPS) — Filtration — Part 45: Morphological profile filters: Segmentation▷ISO 18183-1 Geometrical product specifications (GPS) — Partition — Part 1: Vocabulary and basic concepts▷ISO/CD TR 23850 Geometrical product specifications (GPS) — Association — Mathematical concepts
-
[특집-기술위원회] TC 211 - 지리정보/지리학(Geographic information/Geomatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 211지리정보/지리학(Geographic information/Geomatics)과 관련된 기술위원회는 TC 210과 마찬가지로 1994년 결성됐다. 사무국은 스웨덴 국립표준청(Svenska institutet för standarder, SIS)에서 맡고 있다.위원회는 마츠 올린(Mr Mats Åhlin)가 책임지고 있다. 현재 의장은 피터 파슬로(Mr Peter Parslow)이며 임기는 2024년말까지다. ISO 기술 프로그램 관리자는 하킴 음킨시(Mr Hakim Mkinsi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등이다.범위는 디지털 지리정보 분야의 표준화다. 지구와 관련된 위치와 직간접적으로 연관된 물체나 현상에 관한 정보에 대한 구조화된 표준 세트 확립을 목표로 하고 있다.지리 정보의 범위 내에서 이러한 표준은 데이터 관리를 위한 방법, 도구 및 서비스를 지정할 수 있다. 데이터 관리는 사용자 및 시스템을 위한 데이터 획득, 처리, 분석, 접근, 제시 및 출판이 포함된다.이 작업은 가능한 경우 정보 기술 및 데이터에 대한 적절한 표준과 연결되어야 하며 지리 데이터를 사용하는 부문별 응용 프로그램 개발을 위한 프레임워크를 제공해야 된다.현재 ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준은 97개며 ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준은 26개다. 참여하고 있는 회원은 38개국, 참관 회원은 35개국이다.□ ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준 97개 중 15개 목록▷ISO 6709:2022 Standard representation of geographic point location by coordinates▷ISO 19101-1:2014 Geographic information — Reference model — Part 1: Fundamentals▷ISO 19101-2:2018 Geographic information — Reference model — Part 2: Imagery▷ISO 19103:2015 Geographic information — Conceptual schema language▷ISO 19104:2016 Geographic information — Terminology▷ISO 19105:2022 Geographic information — Conformance and testing▷ISO 19106:2004 Geographic information — Profiles▷ISO 19107:2019 Geographic information — Spatial schema▷ISO 19108:2002 Geographic information — Temporal schema▷ISO 19108:2002/Cor 1:2006 Geographic information — Temporal schema — Technical Corrigendum 1▷ISO 19109:2015 Geographic information — Rules for application schema▷ISO 19110:2016 Geographic information — Methodology for feature cataloguing▷ISO 19111:2019 Geographic information — Referencing by coordinates▷ISO 19111:2019/Amd 1:2021 Geographic information — Referencing by coordinates — Amendment 1▷ISO 19111:2019/Amd 2:2023 Geographic information — Referencing by coordinates — Amendment 2□ ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준 26개 중 15개 목록▷ISO/DIS 19103 Geographic information — Conceptual schema language▷ISO/CD 19109 Geographic information — General feature model and rules for application schema▷ISO/AWI TR 19115-4 Geographic information – Metadata — Part 4: JSON schema implementation of metadata fundamentals▷ISO/DIS 19116 Geographic information — Positioning services▷ISO/AWI TR 19121 Geographic information — Imagery and gridded data▷ISO/AWI 19123-2 Geographic information — Schema for coverage geometry and functions — Part 2: Coverage implementation schema▷ISO/AWI TS 19123-4 Geographic information — Schema for coverage geometry and functions — Part 4: Tiling Schema▷ISO/AWI TS 19124-2 Geographic information — Calibration and validation of remote sensing data and derived products — Part 2: SAR▷ISO/AWI 19127 Geographic information — Geodetic register▷ISO/AWI TS 19130-2 Geographic information — Imagery sensor models for geopositioning — Part 2: SAR, InSAR, lidar and sonar▷ISO/CD 19135 Geographic information registration — Requirements▷ISO/DTS 19144-3 Geographic information — Classification systems — Part 3: Land Use Meta Language (LUML)▷ISO/DIS 19152-2 Geographic information — Land Administration Domain Model (LADM) — Part 2: Land registration▷ISO/FDIS 19152-3 Geographic information — Land Administration Domain Model (LADM) — Part 3: Marine georegulation▷ISO/DIS 19152-4 Geographic information — Land Administration Domain Model (LADM) — Part 4: Valuation information
-
[특집-기술위원회] TC 154 - 상업, 산업 및 행정 분야 프로세스, 데이터 요소 및 문서(Processes, data elements and documents in commerce, industry and administration)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다. 기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다. ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다. 1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다. 이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다. △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136, △1970년 TC 137, TC 138, TC 142, TC 145, △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 등도 포함된다. ISO/TC 154 상업, 산업 및 행정 분야 프로세스, 데이터 요소 및 문서(Processes, data elements and documents in commerce, industry and administration)와 관련된 기술위원회는 1972년 결성됐다. 사무국은 중국 국가표준화관리위원회(国家标准化管理委员会, Standardization Administration of the P. R. C, SAC))에서 맡고 있다. 위원회는 장 지안팡(Mr Jianfang Zhang)이 책임지고 있다. 현재 의장은 유 시(Mr Yu Shi)로 임기는 2024년까지다. ISO 기술 프로그램 관리자는 로라 매튜(Ms Laura Mathew), ISO 편집 관리자는 이본느 헨(Mrs Yvonne Chen) 등으로 조사됐다. 범위는 비즈니스, 행정 프로세스의 국제 표준화 및 등록이다. 또한 개별 조직 내 및 조직간 정보 교환에 사용되는 지원 데이터의 국제 표준화 및 등록, 산업 데이터 분야의 표준화 활동을 지원한다. 다음과 같은 애플리케이션별 메타 표준 개발 및 유지 관리도 포함된다. △프로세스 사양(다른 기술위원회의 개발이 없는 경우) △콘텐츠가 포함된 데이터 사양 △양식 레이아웃(종이/전자) △표준 개발 및 유지 관리 △프로세스 식별(다른 기술위원회의 개발이 없는 경우) △데이터 식별 △EDIFACT 구문의 유지 관리 현재 ISO/TC 154 사무국의 직접적인 책임 하에 발행된 표준은 37개며 SO/TC 154 사무국의 직접적인 책임 하에 개발 중인 표준은 7개다. 참여하고 있는 회원은 17개국, 참관 회원은 28개국이다. □ ISO/TC 154 사무국의 직접적인 책임 하에 발행된 표준 37개 중 15개 목록 ▷ISO 5054-1:2023 Specification for an enterprise canonical model — Part 1: Architecture ▷ISO 6422-1:2010 Layout key for trade documents — Part 1: Paper-based documents ▷ISO 7372:2005 Trade data interchange — Trade data elements directory ▷ISO 8439:1990 Forms design — Basic layout ▷ISO 8440:1986 Location of codes in trade documents ▷ISO 8440:1986/Cor 1:2000 Location of codes in trade documents — Technical Corrigendum 1 ▷ISO 8601-1:2019 Date and time — Representations for information interchange — Part 1: Basic rules ▷ISO 8601-1:2019/Amd 1:2022 Date and time — Representations for information interchange — Part 1: Basic rules — Amendment 1: Technical corrections ▷ISO 8601-2:2019 Date and time — Representations for information interchange — Part 2: Extensions ▷ISO 9735-1:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 1: Syntax rules common to all parts ▷ISO 9735-2:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 2: Syntax rules specific to batch EDI ▷ISO 9735-3:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 3: Syntax rules specific to interactive EDI ▷ISO 9735-4:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 4: Syntax and service report message for batch EDI (message type — CONTRL) ▷ISO 9735-5:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 5: Security rules for batch EDI (authenticity, integrity and non-repudiation of origin) ▷ISO 9735-6:2002 Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 6: Secure authentication and acknowledgement message (message type - AUTACK) □ ISO/TC 154 사무국의 직접적인 책임 하에 개발 중인 표준 7개 목록 ▷ISO/WD 5909 Data interchange processes of blockchain based negotiable maritime bill of lading related to e-Commerce platform ▷ISO/AWI 7372 Trade data interchange — Trade data elements directory ▷ISO 8601-2:2019/DAmd 1 Date and time — Representations for information interchange — Part 2: Extensions — Amendment 1 ▷ISO/AWI 14533-3 Processes, data elements and documents in commerce, industry and administration — Long term signature profiles — Part 3: Long term signature profiles for PDF Advanced Electronic Signatures (PAdES) ▷ISO/WD TR 19626-3 Processes, data elements and documents in commerce, industry and administration —Trusted communication platforms for electronic documents — Part 3: Blockchain-based implementation guideline ▷ISO/DIS 20197-1 Buy-Ship-Pay Reference Data Model — Part 1: Business Requirement Specification (BRS) ▷ISO/DIS 23355 Visibility data interchange between logistics information service providers
-
[특집-기술위원회] TC 149 - 자전거(Cycles)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127, △1969년 TC 130~136, △1970년 TC 137, TC 138, TC 142, TC 145 등도 포함된다.ISO/TC 149 자전거(Cycles)와 관련된 기술위원회는 TC 146, TC 147, TC 148과 마찬가지로 1971년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 마이클 가벨(Mr Michael Gäbel)이 책임지고 있다. 현재 의장은 프랭크 프뤼워(Mr Dipl.-Ing Frank Prüwer)으로 임기는 2025년까지다.ISO 기술 프로그램 관리자는 키르시 실란데르-반 후넨(Mrs Kirsi Silander-van Hunen), ISO 편집 관리자는 빈센조 바주치(M Vincenzo Bazzucchi) 등으로 조사됐다.범위는 성능, 안전, 호환성 및 유지 관리에 대한 용어, 테스트 방법 및 요구 사항을 특별히 참조해 사이클 및 해당 기능, 해당 구성 요소 및 액세서리 분야의 표준화다. 단, 체인 및 치형(tooth profile), 타이어, 림 및 밸브, 장난감 자전거 등은 제외된다.참고로 자건거(Cycle)란 최소한 2개의 바퀴가 있고 특히 페달을 밟거나 페달을 밟을 때 보조 장치를 추가할 수 있는 가능성(예: 전기 모터로 제공)을 통해 해당 차량에 탑승한 사람의 근육 에너지에 의해 전적으로 또는 부분적으로 추진되는 모든 차량을 의미한다. 페달링은 수동 크랭크 사용을 의미하기도 하며 기타 유사한 장치를 말하기도 한다.현재 ISO/TC 149 사무국과 관련해 발행된 표준 29개 중 사무국의 직접적인 책임 하에 발행된 표준은 10개다. 참여하고 있는 회원은 19개국, 참관 회원은 25개국이다.□ ISO/TC 149 사무국의 직접적인 책임 하에 발행된 표준 10개 목록▷ISO 6692:1981 Cycles — Marking of cycle components▷ISO 6695:2015 Cycles — Pedal axle and crank assembly with square end fitting — Assembly dimensions▷ISO 6696:1989 Cycles — Screw threads used in bottom bracket assemblies▷ISO 6697:1994 Cycles — Hubs and freewheels — Assembly dimensions▷ISO 6698:1989 Cycles — Screw threads used to assemble freewheels on bicycle hubs▷ISO 6699:2016 Cycles — Handlebar centre and stem dimensions▷ISO 6701:1991 Cycles — External dimensions of spoke nipples▷ISO 8488:1986 Cycles — Screw threads used to assemble head fittings on bicycle forks▷ISO 8562:2022 Cycles — Stem wedge angle▷ISO 10230:1990 Cycles — Splined hub and sprocket — Mating dimensions□ ISO/TC 149 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 149/SC 1 Cycles and major sub-assemblies ; 발행된 표준 19개, 개발 중인 표준 0개
-
[기획-디지털 ID 기술] ㊶ 존슨컨트롤티코아이피홀딩스, '액세스 컨트롤을 위한 디지털 아이디 프로필의 자동 생성 및 관리' 명칭의 미국 특허 등록 (US 11763613)미국 지적재산권 관리 기업 존슨컨트롤티코아이피홀딩스(Johnson Controls Tyco IP Holdings)에 따르면 2023년 9월19일 '액세스 컨트롤을 위한 디지털 아이디 프로필의 자동 생성 및 관리(Automatic creation and management of digital identity profiles for access control)' 명칭의 미국 특허 (US 11763613)가 등록됐다.본 등록 특허는 2021년 3월 8일에 출원(US 17/195219)된 후 미국 특허청에 의해 심사를 받았다. 패밀리 특허로 PCT 국제 출원(PCT-US2022-070973)이 2022년 3월4일 출원됐다.본 등록 특허는 액세스 제어 시스템을 통해 개인과 관련된 접근 시도를 식별하는 방법에 관한 특허다. 본 등록 특허의 일 실시예에 따르면 억세스 제어 시스템을 통해 개인의 아이디를 확인한다. 개인의 아이디를 확인하는 것에 응답하여 액세스 제어 시스템에 의해 개인에 대한 액세스를 허가한다. 액세스 시도와 동시에 캡처된 개인의 시각 데이터에 기초해 개인의 디지털 아이디 프로파일을 액세스 제어 시스템에 의해 구축한다.
-
[기획-디지털 ID 표준] ⑫산업단체와 포럼 - 신속 온라인 인증(Fast Identity Online, FIDO)디지털 ID(Digital Identity) 분야에서 상호운용(interoperable)이 가능하고 안전한 서비스 보장을 위한 표준에 대한 수요가 증가하고 있다. 다양한 표준 조직 및 산업 기관이 활동하는 이유다.디지털 ID 표준을 개발하는 곳은 유럽표준화기구(European Standardisation Organistions), 국제표준화기구(International Standardisation Organisations), 상업 포럼 및 컨소시엄, 국가기관 등 다양하다.산업단체와 포럼은 공식적으로 표준화 조직으로 간주되지 않지만 디지털 ID 영역을 포함한 특정 영역에서는 사실상의 표준을 제공하고 있다.몇몇의 경우 이들 단체들이 추가 비준을 위해 자신들이 생산한 사양을 ISO/IEC, ITU 통신 표준화 부문(ITU-T), ETSI 등 표준 기관에 제출할 수 있다.이러한 산업단체 및 포럼에는 △인증기관브라우저 포럼(Certification Authority Browser Forum, CA/Browser Forum) △클라우드 서명 컨소시엄(Cloud Signature Consortium, CSC) △국제자금세탁방지기구(Financial Action Task Force, FATF) △신속온라인인증(Fast Identity Online, FIDO) △국제인터넷표준화기구(Internet Engineering Task Force, IETF) △구조화 정보 표준 개발기구(오아시스)(Organization for the Advancement of Structured Information Standards, OASIS) △오픈ID(OpenID) △SOG-IS(Senior Officials Group-Information Systems Security) △W3C(World Wide Web Consortium) 등이다.신속 온라인 인증(Fast Identity Online, FIDO)은 2013년 2월 출범한 개방형 산업협회다. 전 세계 비밀번호에 대한 과도한 의존을 줄이는 데 도움이 되는 인증 표준을 개발하고 홍보하는 것을 사명으로 삼고 있다.디지털 ID와 관련된 내용은 로밍 인증자와 다른 클라이언트/플랫폼 간 통신을 위한 어플리케이션 계층 프로토콜을 설명하는 클라이언트-인증자 프로토콜(Client to Authenticator Protocol, CTAP)이다.다양한 물리적 매체를 사용해 이 어플리케이션 프로토콜을 다양한 전송 프로토콜에 결합하고 있다. 클라이언트-인증자 프로토콜(Client to Authenticator Protocol, CTAP) 관련 목차를 살펴보면 다음과 같다.목차(table of contents)1. Introduction1.1 Relationship to Other Specifications2. Conformance3. Protocol Structure4. Protocol Overview5. Authenticator API5.1 authenticatorMakeCredential (0x01)5.2 authenticatorGetAssertion (0x02)5.3 authenticatorGetNextAssertion (0x08)5.3.1 Client Logic5.4 authenticatorGetInfo (0x04)5.5 authenticatorClientPIN (0x06)5.5.1 Client PIN Support Requirements5.5.2 Authenticator Configuration Operations Upon Power Up5.5.3 Getting Retries from Authenticator5.5.4 Getting sharedSecret from Authenticator5.5.5 Setting a New PIN5.5.6 Changing existing PIN5.5.7 Getting pinToken from the Authenticator5.5.8 Using pinToken5.5.8.1 Using pinToken in authenticatorMakeCredential5.5.8.2 Using pinToken in authenticatorGetAssertion5.5.8.3 Without pinToken in authenticatorGetAssertion5.6 authenticatorReset (0x07)6. Message Encoding6.1 Commands6.2 Responses6.3 Status codes7. Interoperating with CTAP1/U2F authenticators7.1 Framing of U2F commands7.1.1 U2F Request Message Framing ### (#u2f-request-message-framing)7.1.2 U2F Response Message Framing ### (#u2f-response-message-framing)7.2 Using the CTAP2 authenticatorMakeCredential Command with CTAP1/U2F authenticators7.3 Using the CTAP2 authenticatorGetAssertion Command with CTAP1/U2F authenticators8. Transport-specific Bindings8.1 USB Human Interface Device (USB HID)8.1.1 Design rationale8.1.2 Protocol structure and data framing8.1.3 Concurrency and channels8.1.4 Message and packet structure8.1.5 Arbitration8.1.5.1 Transaction atomicity, idle and busy states.8.1.5.2 Transaction timeout8.1.5.3 Transaction abort and re-synchronization8.1.5.4 Packet sequencing8.1.6 Channel locking8.1.7 Protocol version and compatibility8.1.8 HID device implementation8.1.8.1 Interface and endpoint descriptors8.1.8.2 HID report descriptor and device discovery8.1.9 CTAPHID commands8.1.9.1 Mandatory commands8.1.9.1.1 CTAPHID_MSG (0x03)8.1.9.1.2 CTAPHID_CBOR (0x10)8.1.9.1.3 CTAPHID_INIT (0x06)8.1.9.1.4 CTAPHID_PING (0x01)8.1.9.1.5 CTAPHID_CANCEL (0x11)8.1.9.1.6 CTAPHID_ERROR (0x3F)8.1.9.1.7 CTAPHID_KEEPALIVE (0x3B)8.1.9.2 Optional commands8.1.9.2.1 CTAPHID_WINK (0x08)8.1.9.2.2 CTAPHID_LOCK (0x04)8.1.9.3 Vendor specific commands8.2 ISO7816, ISO14443 and Near Field Communication (NFC)8.2.1 Conformance8.2.2 Protocol8.2.3 Applet selection8.2.4 Framing8.2.4.1 Commands8.2.4.2 Response8.2.5 Fragmentation8.2.6 Commands8.2.6.1 NFCCTAP_MSG (0x10)8.2.6.2 NFCCTAP_GETRESPONSE (0x11)8.3 Bluetooth Smart / Bluetooth Low Energy Technology8.3.1 Conformance8.3.2 Pairing8.3.3 Link Security8.3.4 Framing8.3.4.1 Request from Client to Authenticator8.3.4.2 Response from Authenticator to Client8.3.4.3 Command, Status, and Error constants8.3.5 GATT Service Description8.3.5.1 FIDO Service8.3.5.2 Device Information Service8.3.5.3 Generic Access Profile Service8.3.6 Protocol Overview8.3.7 Authenticator Advertising Format8.3.8 Requests8.3.9 Responses8.3.10 Framing fragmentation8.3.11 Notifications8.3.12 Implementation Considerations8.3.12.1 Bluetooth pairing: Client considerations8.3.12.2 Bluetooth pairing: Authenticator considerations8.3.13 Handling command completion8.3.14 Data throughput8.3.15 Advertising8.3.16 Authenticator Address Type9. Defined Extensions9.1 HMAC Secret Extension (hmac-secret)10. IANA Considerations10.1 WebAuthn Extension Identifier Registrations11S ecurity ConsiderationsIndexTerms defined by this specificationTerms defined by referenceReferencesNormative ReferencesInformative ReferencesIDL Index
-
[특집-ISO/IEC JTC 1/SC 17 활동] ⑨Result of voting and comments received on ISO/IEC FDIS 24789-1 소개지난 10월16일 ISO/IEC 공동기술위원회 산하 분과위원회 SC 17은 'Result of voting and comments received on ISO/IEC FDIS 24789-1' 관련된 문서를 배포했다.ISO/IEC JTC 1/SC 17 카드 및 개인 식별을 위한 보안 장치(Cards and security devices for personal identification)는 국제표준화기구(ISO와 국제전기기술위원회(IEC)의 공동 기술 위원회(JTC) ISO/IEC JTC 1의 표준화 분과위원회다.ISO/IEC JTC 1/SC 17의 국제사무국은 영국에 위치한 영국표준협회(BSI)이며 신분증 및 개인 식별 분야 표준을 개발하고 촉진하는 역할을 담당하고 있다. 배포된 문서는 'Result of voting and comments received on ISO/IEC FDIS 24789-1'관련된 투표 정보 및 결과와 관련돼 있다.ISO/IEC 24789-1 표준 프로젝트로 ISO/IEC FDIS 24789-1 (Ed 2) Identification cards — Card service life — Part 1: Application profiles and requirements에 대해 투표한 내용이다. P-Members 18개국이 참여해 18개국(100%) 모두 찬성해 66.66%이상 찬성을 받아 승인됐다.
-
[특집-기술위원회] TC 130 - 그래픽 기술(Graphic technology)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 등이다.△1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104, △1962년 TC 105~TC 107, △1963년 TC 108~TC 111, △1964년 TC 112~TC 115, TC 117, △1965년 TC 118, △1966년 TC 119~TC 122, △1967년 TC 123, △1968년 TC 126, TC 127 등도 포함된다.ISO/TC 130 그래픽 기술(Graphic technology)과 관련된 기술위원회는 1969년 결성됐다. 사무국은 중국 국가표준화관리위원(国家标准化管理委员会, Standardization Administration of China, SAC)에서 맡고 있다.위원회는 메이팡 리(Ms Meifang Li)가 책임지고 있다. 현재 의장은 펑페이 짜오(Mr Pengfei Zhao)로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 마사 카산토산(Mrs Martha Casantosan) 등으로 조사됐다.범위는 인쇄 및 그래픽 기술 분야의 표준화를 다루고 있다. 이 분야는 그래픽 요소(이미지, 텍스트, 라인 아트, 패턴 등)가 생성, 조작, 조립, 전달되고 최종적으로 디지털 제품으로 전자적으로 전달되거나 잉크, 토너 및 기타를 사용해 물리적으로 기판에 전달되는 프로세스의 모든 단계를 다룬다. 마킹 또는 기능성 재료를 생산하고 최종 응용 분야의 요구에 따라 마감 처리된다.ISO/TC 130 표준에는 용어, 시각적 외관 및 제품 품질 평가, 데이터 교환, 프로세스 제어, 관리, 적합성 평가, 환경에 대한 영향 등이 포함되지만 이에 국한되지는 않는다. 뿐만 아니라 관련 재료, 장비 및 시스템에 대한 요구 사항 및 테스트도 수용한다.참고로 ISO/TC 42, TC 6, TC 256, TC 35, IEC/TC 100 및 ISO/IEC JTC 1/SC 28과 같은 다른 TC/SC와 범위가 실제 또는 잠재적으로 중복되는 경우 관련 TC와의 연락 또는 JWG를 통한 조정은 유지되거나 적극적으로 추진돼야 한다.현재 ISO/TC 130 사무국과 관련해 발행된 표준은 115개며 ISO/TC 130 사무국과 관련해 개발 중인 표준은 15개다. 참여하고 있는 회원은 21개국, 참관 회원은 22개국이다.□ ISO/TC 130 사무국 분과위원회(Subcommittee)의 책임 하에 발행된 표준 115개 중 15개 목록▷ISO 2834-1:2020 Graphic technology — Laboratory preparation of test prints — Part 1: Paste inks▷ISO 2834-2:2022 Graphic technology — Laboratory preparation of test prints — Part 2: Liquid printing inks▷ISO 2834-3:2008 Graphic technology — Laboratory preparation of test prints — Part 3: Screen printing inks▷ISO 2836:2021 Graphic technology — Prints and printing inks — Assessment of resistance of prints to various agents▷ISO 2846-1:2017 Graphic technology — Colour and transparency of printing ink sets for four-colour printing — Part 1: Sheet-fed and heat-set web offset lithographic printing▷ISO 2846-2:2007 Graphic technology — Colour and transparency of printing ink sets for four-colour printing — Part 2: Coldset offset lithographic printing▷ISO 5776:2022 Graphic technology — Symbols for text proof correction▷ISO/TS 10128:2009 Graphic technology — Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data▷ISO 11084-1:1993 Graphic technology — Register systems for photographic materials, foils and paper — Part 1: Three-pin systems▷ISO 11084-2:2006 Graphic technology — Register systems for photographic materials, foils and paper — Part 2: Register pin systems for plate making▷ISO 12040:1997 Graphic technology — Prints and printing inks — Assessment of light fastness using filtered xenon arc light▷ISO 12218:1997 Graphic technology — Process control — Offset platemaking▷ISO 12632:2015 Graphic technology — Ink, paper and labels — Requirements on hot alkali penetration and resistance▷ISO 12634:2017 Graphic technology — Determination of tack of paste inks and vehicles by a rotary tackmeter▷ISO 12635:2021 Graphic technology — Plates for offset printing — Dimensions□ ISO/TC 130 사무국 분과위원회(Subcommittee)의 책임 하에 개발 중인 표준 15개 목록▷ISO/DTS 10128 Graphic technology — Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data▷ISO/DIS 12641-1 Graphic technology — Prepress digital data exchange — Colour targets for input scanner calibration — Part 1: Colour targets for input scanner calibration▷ISO/FDIS 12643-1.2 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 1: General requirements▷ISO/FDIS 12643-2.2 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 2: Prepress and press equipment and systems▷ISO/FDIS 12643-3 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 3: Binding and finishing equipment and systems▷ISO/FDIS 12643-4 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 4: Converting equipment and systems▷ISO/FDIS 12643-5 Graphic technology — Safety requirements for graphic technology equipment and systems — Part 5: Manually-fed stand-alone platen presses▷ISO/DIS 12647-2 Graphic technology — Process control for the production of half-tone colour separations, proof and production prints — Part 2: Offset lithographic processes▷ISO/AWI 15076-2 Image technology colour management — Architecture, profile format and data structure — Part 2: Based on ICC.1:2022▷ISO/DIS 15339-1 Graphic technology — Printing from digital data across multiple technologies — Part 1: Principles▷ISO/AWI TS 18621-22 Graphic technology — Image quality evaluation methods for printed matter — Part 22: Evaluation of colour graininess▷ISO/DTS 18621-31 Graphic technology — Image quality evaluation methods for printed matter — Part 31: Evaluation of the perceived resolution of printing systems with the Contrast–Resolution chart▷ISO/AWI 19307 Graphic Technology — Measurement and one-parameter representation of translucency▷ISO/CD TR 23805 Graphic technology — Dry back calculation for offset printing process▷ISO/FDIS 24487 Graphic technology — Processless lithographic plates — Evaluation methods for characteristics and performance□ ISO/TC 130 사무국의 작업그룹(Working Group, WG) 현황▷ISO/TC 130/JWG 7 Joint TC 130 - ICC WG: colour management▷ISO/TC 130/JWG 14 Joint TC 130 - TC 42 - ISO/IEC JTC 1/SC 28 WG: Print quality measurement methods▷ISO/TC 130/TF 3 Communications▷ISO/TC 130/WG 1 Terminology▷ISO/TC 130/WG 2 Prepress data exchange▷ISO/TC 130/WG 3 Process control and related metrology▷ISO/TC 130/WG 4 Media and materials▷ISO/TC 130/WG 5 Ergonomics - Safety▷ISO/TC 130/WG 10 Management of security printing processes▷ISO/TC 130/WG 11 Environmental impact of graphic technology▷ISO/TC 130/WG 12 Postpress
-
[특집-공동기술위원회] ⑥ISO/IEC JTC 1/SC 7 소프트웨어 및 시스템 엔지니어링(Software and systems engineering) 소개 - 1스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC1~TC323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(Working Group, WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등을 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.또한 국제전기기술위원회(International Electro-technical Commission, IEC)는 전기 및 전자 제품의 고품질 인프라와 국제 무역을 뒷받침하는 글로벌 비영리 회원조직이다.기술 혁신, 저렴한 인프라 개발, 효율적이고 지속 가능한 에너지 접근, 스마트 도시화 및 교통 시스템, 기후 변화 완화를 촉진하고 사람과 환경의 안전을 향상시키는 역할을 수행하고 있다. 170개 이상의 국가를 통합하고 전 세계 2만 명의 전문가에게 글로벌하고 중립적이며 독립적인 표준화 플랫폼을 제공한다. 장치, 시스템, 설치, 서비스 및 인력이 필요에 따라 작동함을 구성원이 인증하는 4가지 적합성 평가 시스템을 관리한다.적합성 평가와 함께 정부가 국가 품질 인프라를 구축한다. 모든 규모의 기업이 전 세계 대부분의 국가에서 일관되게 안전하고 신뢰할 수 있는 제품을 사고 팔 수 있도록 하는 기술 프레임워크를 제공하는 약 1만개의 IEC 국제표준을 발행하고 있다.이러한 ISO와 IEC가 공동으로 구성한 기술위원회 ISO/IEC JTC 1 정보 기술(Information technology)에 대해 살펴볼 예정이다. JTC 1은 1987년 결성됐으며 사무국은 미국국립표준협회(American National Standards Institute, ANSI)에서 맡고 있다. 위원회는 리사 라지첼(Mrs Lisa Rajchel)가 책임지고 있다. 현재 의장은 필 웬블롬(Mr Phil Wennblom)으로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), 스티븐 더트널(Mr Stephen Dutnall), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등으로 조사됐다. 범위는 정보기술 분야의 표준화다.현재 ISO/IEC JTC 1의 직접적인 책임 하에 발행된 표준은 517개며 직접적인 책임 하에 개발 중인 표준은 23개다. 참여하고 있는 회원은 40개국, 참관 회원은 62개국이다.공동 기술위원회(Joint Technical Committee, JTC) 산하에서 활동하고 있는 분과위원회(Subcommittee, SC) 중 SC 1, SC 2, SC 6에 이어 SC 7에 대해 살펴보면 다음과 같다.ISO/IEC JTC 1/SC 7 소프트웨어 및 시스템 엔지니어링(Software and systems engineering)과 관련된 분과위원회는 1987년 결성됐다. 사무국은 인도 표준국(Bureau of Indian Standards, BIS)에서 맡고 있다.위원회는 레나 가르그(Ms Reena Garg)이 책임지고 있다. 현재 의장은 선딥 오베로이(Dr Sundeep Oberoi)으로 임기는 2023년까지다.ISO 기술 프로그램 관리자는 앤드류 드라이든(Mr Andrew Dryden), ISO 편집 관리자는 이본느 헨(Mrs Yvonne Chen) 등으로 조사됐다.범위는 소프트웨어 제품 및 시스템 엔지니어링을 위한 프로세스, 지원 도구 및 지원 기술의 표준화다. 참고로 프로세스, 도구 및 기술은 JTC 1 참조 약관의 범위 내에 있으며 JTC 1이 다른 SC에 할당한 특정 도구 및 기술은 제외된다.현재 ISO/IEC JTC 1/SC 7 사무국의 직접적인 책임 하에 발행된 표준은 212개며 개발 중인 표준은 41개다. 참여하고 있는 회원은 37개국, 참관 회원은 24개국이다.□ ISO/IEC JTC 1/SC 7 사무국의 직접적인 책임하에 발행된 표준 및(또는) 프로젝트 212개 중 15개 목록▷ISO 5806:1984 Information processing — Specification of single-hit decision tables▷ISO 5807:1985 Information processing — Documentation symbols and conventions for data, program and system flowcharts, program network charts and system resources charts▷ISO/IEC TR 7052:2023 Software engineering — Controlling frequently occurring risks during development and maintenance of custom software▷ISO/IEC 8631:1989 Information technology — Program constructs and conventions for their representation▷ISO 8790:1987 Information processing systems — Computer system configuration diagram symbols and conventions▷ISO 8807:1989 Information processing systems — Open Systems Interconnection — LOTOS — A formal description technique based on the temporal ordering of observational behaviour▷ISO/IEC TR 10000-1:1998 Information technology — Framework and taxonomy of International Standardized Profiles — Part 1: General principles and documentation framework▷ISO/IEC 10746-1:1998 Information technology — Open Distributed Processing — Reference model: Overview — Part 1:▷ISO/IEC 10746-2:2009 Information technology — Open distributed processing — Reference model: Foundations — Part 2:▷ISO/IEC 10746-3:2009 Information technology — Open distributed processing — Reference model: Architecture — Part 3:▷ISO/IEC 10746-4:1998 Information technology — Open Distributed Processing — Reference Model: Architectural semantics — Part 4:▷ISO/IEC 10746-4:1998/Amd 1:2001 Information technology — Open Distributed Processing — Reference Model: Architectural semantics — Part 4: — Amendment 1: Computational formalization▷ISO/IEC 11411:1995 Information technology — Representation for human communication of state transition of software▷ISO/IEC TR 12182:2015 Systems and software engineering — Framework for categorization of IT systems and software, and guide for applying it▷ISO/IEC/IEEE 12207-2:2020 Systems and software engineering — Software life cycle processes — Part 2: Relation and mapping between ISO/IEC/IEEE 12207:2017 and ISO/IEC 12207:2008□ ISO/IEC JTC 1/SC 7 사무국의 직접적인 책임하에 개발중인 표준 및(또는) 프로젝트 41개 중 15개 목록▷ISO/IEC CD 9837-1 Software and systems engineering — Systems resilience — Part 1: Concepts and vocabulary▷ISO/IEC/IEEE 15026-3 Systems and software engineering — Systems and software assurance — Part 3: System integrity levels▷ISO/IEC CD 19770-5 Information technology — IT asset management — Part 5: Overview and vocabulary▷ISO/IEC PRF 19770-6 Information technology — IT asset management — Part 6: Hardware identification tag▷ISO/IEC CD TS 19770-10 Information technology — IT asset management — Part 10: Guidance for implementing ITAM▷ISO/IEC CD 20582 Software and systems engineering — Capabilities of build and deployment tools▷ISO/IEC AWI TR 24586-1 Software and systems engineering — Agile and DevOps principles and practices — Part 1: Agile principles and practices▷ISO/IEC AWI TR 24586-2 Software and systems engineering — Agile and DevOps principles and practices — Part 2: DevOps principles and practices▷ISO/IEC/IEEE FDIS 24748-1 Systems and software engineering — Life cycle management — Part 1: Guidelines for life cycle management▷ISO/IEC/IEEE FDIS 24748-2 Systems and software engineering — Life cycle management — Part 2: Guidelines for the application of ISO/IEC/IEEE 15288 (System life cycle processes)▷ISO/IEC DIS 24773-2 Software and systems engineering — Certification of software and systems engineering professionals — Part 2: Guidance regarding description of knowledge, skills, and competencies contained in schemes▷ISO/IEC DIS 25002 Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Quality models overview and usage▷ISO/IEC FDIS 25010 Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Product quality model▷ISO/IEC PRF 25019 Systems and software engineering — Systems and software Quality Requirements and Evaluation (SQuaRE) — Quality-in-use model▷ISO/IEC DIS 25040 Systems and software engineering – Systems and software Quality Requirements and Evaluation (SQuaRE) – Quality evaluation framework
-
[기획-디지털 ID 표준] ⑤유럽표준화기구(ESOs) 및 표준 - 소속 기술위원회(TC)디지털 ID(Digital Identity) 분야에서 상호운용(interoperable)이 가능하고 안전한 서비스 보장을 위한 표준에 대한 수요가 증가하고 있다. 다양한 표준 조직 및 산업 기관이 활동하는 이유다. 유럽표준화기구(European Standardisation Organistions, ESOs), 유럽표준화위원회(European Committee for Standardization, CEN), 유럽전기기술표준화위원회(European Committee for Electrotechnical Standardization, CENELEC), 유럽전기통신표준화기구(European Telecommunication Standards Institute, ETSI) 등 디지털 ID 관련 표준을 개발하고 있는 기술위원회에 대해 살펴보면 다음과 같다.먼저 유럽전기통신표준화기구(ETSI)는 유럽의 eIDAS 규정과 전자 거래에 대한 신뢰를 제공하기 위한 국제사회의 일반 요구사항을 지원하는 다수의 표준을 발표했다.특히 ETSI 전자 서명 및 인프라 기술위원회(ETSI Electronic Signatures and Infrastructures Technical Committee)는 서비스 제공업체를 위한 정책, 보안 및 기술 요구사항에 대한 여러 표준을 제정했다.기술위원회(ETSI ESI/TC)는 디지털 서명의 형식, 생성, 검증을 위한 절차, 정책, 신뢰 앵커로서 신뢰할 수 있는 목록을 다룬다.CEN 기술위원회 224(CEN Technical Committee 224, CEN/TC 224)-MACHINE-READABLE CARDS, RELATED DEVICE INTERFACES AND OPERATIONS는 다중 부문 환경에서 보안 요소, 시스템, 운영, 개인정보 보호를 갖는 개인 식별 및 관련 개인 장치와 관련이 있다.기술위원회는 개인 식별, 관련 개인 장치의 상호운용성, 보안을 강화하기 위한 여러 표준을 발표했다. 이 중 CEN 기술위원회 224 내 워킹그룹 17, 18, 19이 디지털 ID와 관련이 있다.다른 실무그룹(Working Group, WG)은 WG 17 : ‘Protection Profiles in the Context of SSCD(secure signature creation device)’ △WG 18 : ‘Biometrics’ △WG 19 : ‘Breeder Documents' 등이다. 최근 유럽 디지털 지갑 EUDI Wallet 표준을 개발하기 위해 WG 20이 임시로 구성됐다.CEN/TC 224는 다중 부문 환경에서 개인 식별 및 관련 개인 장치, 시스템, 운영 및 개인 정보 보호의 상호 운용성과 보안을 강화하기 위해 표준을 개발하고 있다.여기에는 전자 식별, 전자 서명, 지불 및 청구, 출입, 국경 통제와 같은 애플리케이션 및 서비스와 같은 작업을 포함하고 있다. 또한 △카드, 모바일 장치 및 관련 인터페이스와 같이 폼 팩터와 독립적인 보안 요소를 갖춘 개인 장치 △인증, 기밀성, 무결성, 생체 인식, 개인 데이터 및 민감한 데이터 보호를 포함한 보안 서비스 △수용 장치, 서버, 암호화 모듈과 같은 시스템 구성 요소 등도 해당된다.CEN/TC 224 다중 부문 환경은 정부·시민, 교통, 은행, 전자 보건과 같은 부문 뿐만 아니라 카드 제조업체, 보안 기술, 적합성 평가기관, 소프트웨어 제조업체와 같은 공급 측면의 소비자 및 공급자가 포함된다. 참고로 CEN 기술 위원회 224 내 실무 그룹(WG)은 다음과 같다.▷CEN/TC 224/WG 1 - ICC physical characteristics▷CEN/TC 224/WG 2 - General concepts for ICC systems▷CEN/TC 224/WG 3 - Device interface characteristics▷CEN/TC 224/WG 6 - User Interface▷CEN/TC 224/WG 7 - PIN presentation▷CEN/TC 224/WG 8 - Thin flexible cards▷CEN/TC 224/WG 9 - Telecommunication applications▷CEN/TC 224/WG 10 - Intersector electronic purse▷CEN/TC 224/WG 11 - Transport applications▷CEN/TC 224/WG 12 - Health applications▷CEN/TC 224/WG 15 - European citizen card▷CEN/TC 224/WG 16 - Application Interface for smart cards used as Secure Signature Creation Devices▷CEN/TC 224/WG 17 - Protection Profiles in the context of SSCD▷CEN/TC 224/WG 18 - Interoperability of biometric recorded data▷CEN/TC 224/WG 19 - Breeder Documents▷CEN/TC 224/WG 20 - Ad Hoc Group on European Digital Identity WalletsCEN/CENELEC 공동 기술위원회 19(CEN/CENELEC Joint Technical Committee 19)는 블록체인(Blockchain) 및 분산 원장 기술(Distributed Ledger Technologies)을 다루는 위원회다.특히 실무 그룹 1(Working Group 1) : 분산형 신원 관리(Decentralised Identity Management)는 ISO 카운터파트너 ISO 기술위원회 307( ISO Technical Committee 307)과 긴밀한 접촉을 유지하고 있다.분산형 ID 관리(decentralised identity management) 및 DLTs(Distributed Ledger Technologies)에 의해 제공되는 지원 기능을 위한 프로세스, 역할, 관행에 대한 것이다. 식별자, 키, 증거 레지스트리, 트러스트 앵커(trust anchors) 관리를 포함한다.실무그룹 2(WG 2)는 환경 지속가능성(CEN/CLC/JTC 19/WG 2 - Environmental sustainability)을 다루고 있다.